Mountfield 4140H Bedienerhandbuch PDF herunterladen (Seite 11)

ENGLISH

3.3.3 Installing the battery

1. Open the engine casing and position the battery

in the appropriate place. See fig. 5.

2. Secure the battery in position.

3. First connect the red cable to the battery’s

positive terminal (+).

4. Connect the black cable to the battery’s

negative terminal (-).

If the cables are interchanged, the

generator and the battery will be

damaged.

The engine must never be driven with

the battery disconnected. There is a risk

of serious damage to the generator and

the electrical system.

3.4 SEAT

NOTE! To facilitate installation of the seat,

apply a drop of oil to the four screws before

screwing them into the seat.

Release the catch (2:S) and fold up the seat

bracket.

Install the mounting in the rear (upper) holes as

follows:

1. Install the shoulder washers (2:F) on the screws

(2:K).

2. Insert the screws through the slots in the

bracket. Place a washer (2:I) between the seat

and the bracket.

3. Tighten the screws in the seat. Tightening

torque: 9±1.7 Nm.

If the screws are tightened more than

9±1.7 Nm, the seat will be damaged.

4. Check that the seat moves easily in the slots in

the bracket.

Install the mounting in the front (lower) holes as

follows:

1. Install the screw knobs (2:H) on the screws

(2:G).

2. Install a washer (2:I) on each screw.

3. Insert the screws through the slots in the bracket

and tighten by hand in the seat.

4. Fold the seat down and place it in the desired

position.

5. Tighten the screw knobs (2:H) by hand.

The screw knobs (2:H) and the seat will

be damaged if tools are used.

The seat can be folded. If the machine is parked

outside when it is raining, fold the seat forward to

protect the seat cushion from getting wet.

The seat is locked. To fold the seat up or down,

release the catch (2:S).

3.5 STEERING WHEEL

In order to minimise the axial play in the steering

column, the shim washers (6:D) and/or (6:E) must

be installed on the steering column between the

steering column jacket and the bracket as follows.

1. Install the steering column jacket on the

steering column and secure by knocking in one

of the pins (6:C) approximately 1/3 of its

length.

2. Pull the steering column jacket and the steering

column up.

3. From the outside, check whether no washers,

the 0.5 mm washer, the 1.0 mm washer or both

washers can be inserted into the gap. The

washer/washers must not be forced in, as there

must be a little axial play.

4. Pull out the pin and dismantle the steering

wheel jacket.

5. Install the washer/washers in accordance with

point 3 above.

6. Install the steering column jacket on the

steering column and secure by knocking in both

the pins fully. Use a counterhold.

3.6 TOWING HITCH

See fig. 7. Screw the towing hitch (J) into the two

holes on the underside of the rear axle using screws

(L+K). Tighten the screws properly.

Tightening torque: 22 Nm.

3.7 QUICK-RELEASE MOUNTINGS

The quick-release mountings and installation

instructions are supplied in a separate box.

Install the quick-release mountings on the front

axles of the machine.

3.8 TYRE PRESSURE

Check the air pressure in the tyres. Correct air

pressure:

Front: 0.6 bar (9 psi)

Rear: 0.4 bar (6 psi)

3.9 ACCESSORIES

For the installation of accessories, see separate

installation guide supplied with each accessory.

Note: The cutting deck is regarded as an accessory

here.

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 85 86

Kommentare zu diesen Handbüchern

Keine Kommentare

Mountfield 4140H Bedienerhandbuch Seite 11

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Traktor Mountfield 4140H